Powder size versus velocity
- JonnyV
- Posts: 561
- Joined: Mon Jun 28, 2021 3:52 pm
- Location: Living in a van down by the river eatin’ Govt cheese
- Contact:
Powder size versus velocity
Hey everybody, I’ve been told that your velocity will go up slightly if you move to a smaller granulation of powder. For instance, 2F might shoot a little bit faster than 1.5 F… Does the same hold true for 3F? Is anybody here tried 3F in a 45-90 or 45-100? What were your results? Thanks for any help!
-
- Posts: 212
- Joined: Mon Mar 09, 2009 4:53 am
- Location: New Mexico
Re: Powder size versus velocity
While I only have a 45 2.1", I found that FFFg gave me more fouling than FFg, so I switched to all FFg. I know it may be apples to oranges, but it was my experience. The increase in velocity was not worth it.
- JonnyV
- Posts: 561
- Joined: Mon Jun 28, 2021 3:52 pm
- Location: Living in a van down by the river eatin’ Govt cheese
- Contact:
Re: Powder size versus velocity
HDH, I assume that you’re wiping between each shot correct? What is the fouling reaching a point where the wipers were having a hard time controlling it?
-
- Posts: 449
- Joined: Wed Dec 03, 2014 5:00 pm
- Location: Florida
Re: Powder size versus velocity
JonnyV
I shoot an original Ballard #7 long range, 44/100. 535gr. paper patched bullet. I get my highest velocity, least fouling, lowest S.D. with uncompressed 1f Swiss….1360fps.
Tom
I shoot an original Ballard #7 long range, 44/100. 535gr. paper patched bullet. I get my highest velocity, least fouling, lowest S.D. with uncompressed 1f Swiss….1360fps.
Tom
- desert deuce
- Posts: 3863
- Joined: Mon Apr 14, 2008 10:51 pm
- Location: Rio Rico, Arizona
Re: Powder size versus velocity
There you go Tom, divulging that Top Secret information again.
Sometimes you get the chicken, and sometimes you get the feathers!
-
- Posts: 449
- Joined: Wed Dec 03, 2014 5:00 pm
- Location: Florida
Re: Powder size versus velocity
D.D.
It probably went over his head anyway
Tom
It probably went over his head anyway
Tom
- JonnyV
- Posts: 561
- Joined: Mon Jun 28, 2021 3:52 pm
- Location: Living in a van down by the river eatin’ Govt cheese
- Contact:
Re: Powder size versus velocity
Yup sure did…
-
- Posts: 2897
- Joined: Wed Feb 03, 2010 3:21 pm
- Location: Montana
-
- Posts: 203
- Joined: Wed Aug 17, 2011 10:57 am
Re: Powder size versus velocity
I seem to remember case stretching up to mid case separations when using 3F in the larger cases and bottlenecks.
It does okay in straight 38's. My wife's 38-55 shoots fine with 3f, never had a separation or cracked case.
I've seen quite a few .45-70's at long range matches where there were separations using 3f trying to get some more velocity.
It does okay in straight 38's. My wife's 38-55 shoots fine with 3f, never had a separation or cracked case.
I've seen quite a few .45-70's at long range matches where there were separations using 3f trying to get some more velocity.
-
- Posts: 525
- Joined: Tue May 19, 2015 9:19 am
Re: Powder size versus velocity
Probably the better question would be to ask the top five shooters in BPTR what powder they use. Look at the match results and ask those guys what they use to win. Velocity for the sake of velocity doesn't always equate to the most accurate load. Making it go faster doesn't always mean you'll make it more accurate. In a 45-90 or 45-100 you have enough case to develop an accurate load with whatever powder works.
- JonnyV
- Posts: 561
- Joined: Mon Jun 28, 2021 3:52 pm
- Location: Living in a van down by the river eatin’ Govt cheese
- Contact:
Re: Powder size versus velocity
SFogler wrote: ↑Sat Feb 11, 2023 12:18 am Probably the better question would be to ask the top five shooters in BPTR what powder they use. Look at the match results and ask those guys what they use to win. Velocity for the sake of velocity doesn't always equate to the most accurate load. Making it go faster doesn't always mean you'll make it more accurate. In a 45-90 or 45-100 you have enough case to develop an accurate load with whatever powder works.
All excellent points. We’re not pursuing velocity just for velocity sake, rather doing an experiment trying to observe the transonic phase of flight. Our bullets go transonic very quickly after leaving the muzzle. Even back when I shot smokeless powder and was running 1425 ft./s. The bullet would go transonic within 300 yards.
Might lead to nothing, but there could be some information there worth learning.
-
- Posts: 865
- Joined: Mon Jan 07, 2013 9:07 am
- Location: St. Albert, Alberta
Re: Powder size versus velocity
I used Swiss FFFg in both my .40-65 and .40-60 Maynard rifles with 30" barrels.
Generally going from 1.5 F to 3 F can increase velocities by 10%.
I never had fouling problems using Swiss FFFg using a good quality lube and with ensuring I properly blew down my barrel between shots.
I used Alberta Schuetzen Lube.
I believe you get more fouling from the incompletely burned large granules whereas the finer powder completely burns in the barrel providing more pressure.
Generally going from 1.5 F to 3 F can increase velocities by 10%.
I never had fouling problems using Swiss FFFg using a good quality lube and with ensuring I properly blew down my barrel between shots.
I used Alberta Schuetzen Lube.
I believe you get more fouling from the incompletely burned large granules whereas the finer powder completely burns in the barrel providing more pressure.
- JonnyV
- Posts: 561
- Joined: Mon Jun 28, 2021 3:52 pm
- Location: Living in a van down by the river eatin’ Govt cheese
- Contact:
Re: Powder size versus velocity
SchuetzenDave wrote: ↑Sat Feb 11, 2023 9:49 pm I used Swiss FFFg in both my .40-65 and .40-60 Maynard rifles with 30" barrels.
Generally going from 1.5 F to 3 F can increase velocities by 10%.
I never had fouling problems using Swiss FFFg using a good quality lube and with ensuring I properly blew down my barrel between shots.
I used Alberta Schuetzen Lube.
I believe you get more fouling from the incompletely burned large granules whereas the finer powder completely burns in the barrel providing more pressure.
Thanks for reading the original question Dave! Now, have you tried different bullet weights with these powders? Weee the results consistent?
-
- Posts: 865
- Joined: Mon Jan 07, 2013 9:07 am
- Location: St. Albert, Alberta
Re: Powder size versus velocity
I used a 410 grain Boomer Money and a 422 grain Paul Jones Creedmoor in both the calibers using the same amount of Swiss FFFg.
The heavier 422 grain Paul Jones had more Kinetic Energy from being heavier (less susceptible to wind drift) plus this Creedmoor bullet had better dynamic stability resulting in it getting a bit more accuracy at longer distances (over 500 yards).
The straighter walled .40-60 Maynard had better bullet concentricity in the straighter case and the Paul Jones Creedmore bullet was more successful knocking down Rams.
However both were very effective of shooting tight groups at 800 meters.
The heavier 422 grain Paul Jones had more Kinetic Energy from being heavier (less susceptible to wind drift) plus this Creedmoor bullet had better dynamic stability resulting in it getting a bit more accuracy at longer distances (over 500 yards).
The straighter walled .40-60 Maynard had better bullet concentricity in the straighter case and the Paul Jones Creedmore bullet was more successful knocking down Rams.
However both were very effective of shooting tight groups at 800 meters.
-
- Posts: 865
- Joined: Mon Jan 07, 2013 9:07 am
- Location: St. Albert, Alberta
Re: Powder size versus velocity
Also to achieve good accuracy with the Money bullet at the longer ranges with it's poorer dynamic stability I had to get the velocities up to 1250 FPS or more.