45-110 Norma Basic Brass Resizing PROBLEM
-
- Posts: 1151
- Joined: Mon Oct 28, 2013 1:33 pm
Re: 45-110 Norma Basic Brass Resizing PROBLEM
I use CH4D Dies for my 120
-
- Posts: 1151
- Joined: Mon Oct 28, 2013 1:33 pm
Re: 45-110 Norma Basic Brass Resizing PROBLEM
I use CH4D Dies for my 120
-
- Posts: 1151
- Joined: Mon Oct 28, 2013 1:33 pm
Re: 45-110 Norma Basic Brass Resizing PROBLEM
I use CH4D Dies for my 120
-
- Posts: 1151
- Joined: Mon Oct 28, 2013 1:33 pm
Re: 45-110 Norma Basic Brass Resizing PROBLEM
I use CH4D Dies for my 120
-
- Posts: 1584
- Joined: Sat Feb 15, 2003 2:03 pm
Re: 45-110 Norma Basic Brass Resizing PROBLEM
I find that CH4D dies work the best with my 100. I'm not sure type of lube matters? I use STP. Have for decades. Same pint. Make sure die is clean, then use extremely small amount of lube applied with fingers. Extremely light coat. Long BP cases from 100 on up are especially prone to lube dents. If you don't use extremely light coat of lube, it will pile up as you run long case through die, causing dents.
Re: 45-110 Norma Basic Brass Resizing PROBLEM
All of my BPCR dies (40-65, 45-70, 45-100, and 50-90) are RCBS. I do have some Redding competition bullet seating dies as well as Shiloh's inline seating dies. They all work well. Once my brass has been fire formed they only see a Meacham bushing neck sizer. Basically clean then neck size and load. Annealed as needed.
- Lumpy Grits
- Posts: 7680
- Joined: Tue Jan 28, 2003 7:58 pm
- Location: Springfield, Missouri-U.S.A. Earth
Re: 45-110 Norma Basic Brass Resizing PROBLEM
http://www.sageoutfitters.com/page/page/7184637.htm
Case lube-You can also get it in 1 gal bottle.
http://www.sageoutfitters.com/catalog/i ... 456454.htm
G.
Case lube-You can also get it in 1 gal bottle.
http://www.sageoutfitters.com/catalog/i ... 456454.htm
G.
"Hav'n you along, is like loose'n two good men"
-
- Posts: 3857
- Joined: Tue Nov 23, 2004 12:52 pm
Re: 45-110 Norma Basic Brass Resizing PROBLEM
Never ever had any problems fl sizing Norma 2.9 or Starline 50-2.5 with LYMAN dies .Had to anneal the Starline but not the Norma use the imperial die sizing wax. And don't cut anymore brass that short again. bobw
bobw
- Cm1green
- Posts: 54
- Joined: Wed Nov 15, 2017 1:13 pm
- Location: Colorado Springs, CO
- Contact:
Re: 45-110 Norma Basic Brass Resizing PROBLEM
Thanks Grits that is a great site. I will be getting some stuff from thim after my payday.
1. “The difficult we do now the impossible takes just a little longer”
2. “CAN DO”
2. “CAN DO”
- Lumpy Grits
- Posts: 7680
- Joined: Tue Jan 28, 2003 7:58 pm
- Location: Springfield, Missouri-U.S.A. Earth
Re: 45-110 Norma Basic Brass Resizing PROBLEM
"Hav'n you along, is like loose'n two good men"
- Cm1green
- Posts: 54
- Joined: Wed Nov 15, 2017 1:13 pm
- Location: Colorado Springs, CO
- Contact:
Re: 45-110 Norma Basic Brass Resizing PROBLEM
Thanks all for the inputs and help it is greatly appriciated got them sized and ready!
1. “The difficult we do now the impossible takes just a little longer”
2. “CAN DO”
2. “CAN DO”