Looking for 45-70 mold
-
- Posts: 161
- Joined: Fri Jan 18, 2019 3:58 pm
Looking for 45-70 mold
I see mention of the BACO 459542M3 but it is not in stock. So I am thinking to go with the Lyman 457132 if accessible. But the question is if there is an alternative supplier to BACO for the same BACO 459542M3 bullet. I looked at Accurate and it seems they only do flat nosed most like due to limits of lathe tooling. Is there anyone else?
I have been using the 457121-PH with good results at shorter ranges but want to extend beyond 200 yards.
Thank you,
Charles
I have been using the 457121-PH with good results at shorter ranges but want to extend beyond 200 yards.
Thank you,
Charles
-
- Posts: 312
- Joined: Tue May 15, 2018 6:42 pm
- Location: Western,Pa
Re: Looking for 45-70 mold
Just call Buffalo Arms and place it on order, they will have it ready as soon as it is in its turn.
-
- Posts: 270
- Joined: Wed Feb 14, 2018 4:18 pm
- Location: Nine Mile Falls Wa
Re: Looking for 45-70 mold
Most BACO molds are not in stock but made to order. They are far better than the Lyman molds as far as Im concerned. I own quite a few bacos and several of the others. They just seem easier to cast with and I get nicer more consistent bullets. It normally dosent take long to get your molds. Mike
- J.B.
- Posts: 644
- Joined: Tue Apr 20, 2004 10:31 pm
- Location: Australia
Re: Looking for 45-70 mold
Dont hesitate to place an order with BACo for the design you're after. I doubt very much you'll be waiting very long. While I've used and still have several Lyman and RCBS moulds, I'd give the nod to Kal, BACo, Steve Brooks and Accurate every time. The number in BACo's mould design inventory would make it prohibitive to hold shelf stock. I've rarely waited more than a few weeks for a BACo mould but of course it depends how many are ahead of you. You wont be disappointed. A very good product from a very supportive company. Give them a call and get it rolling. To that I'd just add that the 1/8" minimum meplat in any Acc. mold design, at least in 44 cal or above, 'for me at least'...has not manifested itself as a problem with regard bullet performance at long range. I remain the weak link... every time.
J.B.
J.B.
"an experimental weapon..with experimental ammunition ? ...Lets experiment "
- Silver Eagle
- Posts: 33
- Joined: Wed Jan 24, 2007 12:36 pm
- Location: Hubbard, Ohio
Re: Looking for 45-70 mold
Check out Tom over at www.accuratemolds.com
All are lathe bored and sized to your desired alloy.
I have one of his 46-507C in iron blocks.
I can hold +/- 1/2 grain when casting and hold 3/4” to 1” groups off the bench at 100 yards for 5 shots…
All are lathe bored and sized to your desired alloy.
I have one of his 46-507C in iron blocks.
I can hold +/- 1/2 grain when casting and hold 3/4” to 1” groups off the bench at 100 yards for 5 shots…
You do not have the required permissions to view the files attached to this post.
- Don McDowell
- Posts: 7633
- Joined: Thu Nov 29, 2007 2:04 pm
- Location: Ft. Laramie Wy
- Contact:
Re: Looking for 45-70 mold
As has been already mentioned call Baco and order your bullet
It will be in your mailbox in a couple 3 weeks usually
It will be in your mailbox in a couple 3 weeks usually
AKA Donny Ray Rockslinger
-
- Posts: 8428
- Joined: Wed Oct 12, 2005 10:28 pm
- Location: Not Far enough NW in Illinois
Re: Looking for 45-70 mold
I have two brass moulds that Tom made for me. One for the .444 Marlin and the other for the .30-30 93 Marlin rifle.
I will say the .444 mould is a double cavity and both bullets drop out identical in weight and diameters. It's the only multi cavity mould that does this that I have used in the past for pistol bullseye matches.
That small meplat wont hurt a thing as far as you want to shoot it.
I had Tom duplicate the Lyman 121PH for me at a proper diameter for the .45 caliber and he put it in his catalog. I have shot that bullet out to 1026 yards and it hit more than it missed in a good Montana breeze. Don't count the flat nosed bullets short. They work.
Ba will make your mould and you will get it in short time.
I will say the .444 mould is a double cavity and both bullets drop out identical in weight and diameters. It's the only multi cavity mould that does this that I have used in the past for pistol bullseye matches.
That small meplat wont hurt a thing as far as you want to shoot it.
I had Tom duplicate the Lyman 121PH for me at a proper diameter for the .45 caliber and he put it in his catalog. I have shot that bullet out to 1026 yards and it hit more than it missed in a good Montana breeze. Don't count the flat nosed bullets short. They work.
Ba will make your mould and you will get it in short time.
The reason a dog has so many friends is because he wags his tail instead of his tongue.
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery"Winston Churchill
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery"Winston Churchill
-
- Posts: 34
- Joined: Tue Jan 10, 2012 5:24 pm
- Location: Western Washington State
Re: Looking for 45-70 mold
Don't let the "not in stock" deter you from placing your BACO mold order. Get on the phone, you will have your mold in a surprisingly short period of time. In the end, you will not be disappointed in your decision.
- Lumpy Grits
- Posts: 7675
- Joined: Tue Jan 28, 2003 7:58 pm
- Location: Springfield, Missouri-U.S.A. Earth
Re: Looking for 45-70 mold
Give Steve Brooks a call
https://www.brooksmoulds.com/
https://www.brooksmoulds.com/
"Hav'n you along, is like loose'n two good men"
-
- Posts: 161
- Joined: Fri Jan 18, 2019 3:58 pm
Re: Looking for 45-70 mold
All,
Thank you for the info. It has given me several options to chase down.
Charles
Thank you for the info. It has given me several options to chase down.
Charles