45-75 Win

Discussions of powders, bullets and loading information.

Moderators: Kirk, Lucinda

Post Reply
User avatar
deerhuntsheatmeup
Posts: 2258
Joined: Sat Feb 15, 2003 6:36 pm
Location: Mississippi

45-75 Win

Post by deerhuntsheatmeup » Wed Sep 01, 2004 5:18 am

A shooyLater, David Barfielding pardner of mine has the opportunity to purchase an original 1885 in 45-75. From the pictures of the cartridge, it looks like basic .50 brass necked down to .45 cal. Does anyone have any experience loading and shooting a 45-75?

Later, David Barfield
General Rustie
Oiling Director
FES Society
It's hard to have a bright light experience, when you are living in the light.

User avatar
JAGG
Posts: 589
Joined: Tue Aug 12, 2003 5:28 pm

Post by JAGG » Thu Sep 02, 2004 12:03 pm

DHHMU ! Get a copy Cartridges of the World ! If i remember right some people were making cases out od 348 win brass ! But today 45/75 brass is being made again ! 300 to 350 gr bullets is what they use to be rifled for so check your twist ! JAGG
JAGG

User avatar
KHR
Posts: 277
Joined: Wed Jan 21, 2004 3:16 pm
Location: Lone Star State, Central TX

Post by KHR » Thu Sep 02, 2004 1:21 pm

David,
You might want to have your friend doublecheck the rifle model and caliber. The 45/75 was intially designed for the 1876 winchester. The 45/75 used a shortened case (shorter than 45/70) to cycle in the '76 toggle link action (based upon the 1873 action) I did not know that the 1885 (or the 1886) was chambered for this round. If the gun is a 1876 with good bore it can be very accurate, my '76 is a 45/60 and is a very good shooter (but it has a mint bore). I use the lyman gould 330gn hollow point and it shoots well. MLV's book on lever actions has a good chapter on the 45/75.
:-)
keith
Some originals and some Shilohs.
Molon Labe

MLV
Posts: 3688
Joined: Tue Jan 21, 2003 5:21 pm
Location: Livingston, MT
Contact:

Post by MLV » Thu Sep 02, 2004 7:23 pm

The .45-75 WCF was the introductory cartridge for the Model 1876 Winchester, but it was also chambered in the Model 1885 "High Wall", as were about 80 or 90 other rounds. Never for the Model 1886.

It uses a bottlenecked case 1.89 inches long. Workable cases can be made from .348 Winchester brass, but they may form a slight bulge about 1/4 inch ahead of the rim. Ready to load ones by Bertram can be bought from Huntington Die Specialties in Oroville, CA. They are expensive. Rifling twist rate for a .45-75 is proper for 350 grain flat nose bullets. Rate is 1 turn in 26 inches according to George Madis' THE WINCHESTER BOOK.

And I hope that helps.

Blackstone
Posts: 2
Joined: Thu May 29, 2014 11:28 am

Re: 45-75 Win

Post by Blackstone » Sun Feb 24, 2019 7:14 pm

I make 45-75 brass out of starline 50-90 brass buy reducing the rim diameter, cutting back to 1.89 and running into the resising die

77 sharps
Posts: 243
Joined: Thu Nov 11, 2010 9:45 pm
Location: N. CA

Re: 45-75 Win

Post by 77 sharps » Sun Feb 24, 2019 8:15 pm

Comparing the original.45-75 WCF cartridge I have to my Starline .50-110 WCF , I would form .45-75 cases from the .50-110 Starline brass. BACo. has the brass in stock.

User avatar
Lumpy Grits
Posts: 7252
Joined: Tue Jan 28, 2003 7:58 pm
Location: The Mojave Desert...Palmdale, Ca. U.S.A. Earth

Re: 45-75 Win

Post by Lumpy Grits » Mon Feb 25, 2019 8:51 am

Blackstone wrote:
Sun Feb 24, 2019 7:14 pm
I make 45-75 brass out of starline 50-90 brass buy reducing the rim diameter, cutting back to 1.89 and running into the resising die
Just an FYI-You replied to a almost 15 year old post.
May want to start a new thread.....
Good luck...
Gary
"Hav'n you along, is like loose'n two good men"

User avatar
kenny s
Posts: 620
Joined: Sat Nov 07, 2015 8:14 am
Location: Venice FL

Re: 45-75 Win

Post by kenny s » Mon Feb 25, 2019 10:03 am

had (and just sold) a 76 original in 45 60, very accurate round. the bullet is the same and
I used a Gould hollow point mold. as per the original. Ken

Post Reply