Saeco #022 bullet question

Share your tales (tall or otherwise) of hunting adventures.

Moderators: Kirk, Lucinda

Post Reply
pete
Posts: 2258
Joined: Tue Nov 12, 2002 10:16 pm
Location: Colorado

Saeco #022 bullet question

Post by pete »

Last week my wife and I went deer hunting and I lucked out and managed to kill a deer with the same rifle and load as I used for the antelope we got earlier. We had a fun time including the mile walk back to the truck in the dark after the deer was skinned and hung in a tree. Well ok my wife didn't think the walk back was that much fun but you have to hand it to a woman that'll do that. :)
The shot was 130 yds with a 45-70 shooting a Lyman 457125 Govt. bullet out of pure lead at 1240 fps. The entance was behind the shoulder angling back hitting a rib on the far side and exited leaving a 5/8 dia hole. The deer ran 165 yds.
The performance was a little disapointing compared to the 420 gr flat noses I've used before. The antelope was hit high breaking the back and required a coup de gras which while fatal wasn't really impressive either.

I want to stick with a heavier bullet because of the wind and have been looking at the Saeco #022 500 gr. flat point. Has anybody used this bullet and if so what do you think? I know there are some devout Govt. bullet users here so I expect some disagreements :)
Dan O
Posts: 737
Joined: Sun May 01, 2005 3:05 pm
Location: Great Falls Montana

Post by Dan O »

http://www.brooksmoulds.com

Check out this site by Steve Brooks. He has a flat point hunting bullet that you can get in any weight you wish. I have one that gives a 490 grain 30-1 that is accurate. I haven't shot anything with it yet but have no doubt it will perform pretty well. It is a design that Brooks recommended when I told him what I was looking for.

Dan
rdnck
Posts: 1885
Joined: Tue Oct 29, 2002 9:33 pm
Location: Woodlawn,Texas

The hit

Post by rdnck »

pete--I suspect that the reason your deer ran 165 yards after you hit him with the round nosed Govt. bullet was the ANGLE you hit him at. If you hit him BEHIND the shoulder angling BACK towards the ribs, the bullet was going away from the lungs and heart which gives the quickest put down. At the angle you had, if you had him IN FRONT of the shoulder and angled back, you would have gotten into the lungs and he would not have gone as far.

It's a fine line, but you need to hit the animal in front of the diaphragm for the quickest put down, regardless of the nose shape. Shoot straight, rdnck.
Chairman, Phd
Caddo Lake Chapter
FES
Charter Member FBASS

Charter Member OGANT
Michael Johnson

Jones 45017

Post by Michael Johnson »

Pete, I have used the Jones 45017 flat nose bullet out of my 45-70 Shiloh with good success on deer and bison. They weigh 485 grains when cast in pure lead. - Mike
pete
Posts: 2258
Joined: Tue Nov 12, 2002 10:16 pm
Location: Colorado

Post by pete »

Dan and Michael ;
Thanks for the replies. Both of those look good. I have a Brooks flat point of my design that's 430 (pure lead) and 420 (20-1) but am hoping to get a heavier bullet from a budget mould so to speak. If I can't find what I'm looking for then the ones you mention are what I'll get. I want a new silhouette bullet too hence the predicament. :)

rdnck;
Thanks. Since I know most people don't want a long drawn out story I try to get to a point quickly and leave a thing or two out. The bullet path wasn't a severe angle and I did get both lungs and she had foamy blood in her mouth. The bullet clipped a rib going in and centered one going out and never was aft of the lung cavity. I've shot enough animals to know that such things happen but this example combined with the fairly small exit hole on the antelope finishing shot which was shot at 2 feet leaves me concerned.

It appears that if I do get this mould I'll be the only one on the forum to shoot one. Printing out an image that's adjusted to .458 dia. the meplat looks to be about .230 and the grooves are such that it won't use alot of case room. But I was hoping somebody might know for sure.
Kurt
Posts: 8428
Joined: Wed Oct 12, 2005 10:28 pm
Location: Not Far enough NW in Illinois

Post by Kurt »

Here you go Pete, get a few and see how they work out for you.


http://www.westernbullet.com/saeco022.html
The reason a dog has so many friends is because he wags his tail instead of his tongue.

"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery"Winston Churchill
pete
Posts: 2258
Joined: Tue Nov 12, 2002 10:16 pm
Location: Colorado

Post by pete »

Thanks Kurt great idea I appreciate it. I'll order some when they get some in stock.
mannyspd1
Posts: 437
Joined: Wed Apr 06, 2005 7:53 am

Post by mannyspd1 »

Pete,

I have tried the bullet in my two 45-70's, but I like the 457125 better.

I still have a few left and took some measurements for you:

1.245 oal, 520 grns. @ 40:1, base to bottom of first driving band is .540, base to top of first driving band is .637, meplat is .260.

I just couldn't get the accuracy I wanted in my rifles, but it may work better for you.

I got mine from Mt. Baldy bullets. Frank will cast them 20, 30, or 40:1 if you ask.

Manny
Speak softly and carry a big stick...the exercise of intelligent forethought and of decisive action sufficiently far in advance of any likely crisis
TR
pete
Posts: 2258
Joined: Tue Nov 12, 2002 10:16 pm
Location: Colorado

Post by pete »

Mannyspd1;

Thanks alot that's what I was looking for. Funny thing is that yesterday afternoon before I saw your post I just went ahead and ordered a mould from Midway. I did it because I checked for months this year and Midway was always out of stock and with Western Bullet being out of trial bullets too I thought I might as well get one before the moulds are gone again.
The meplat you measured is a little bigger than what I wanted. I measured the images from Saeco and hoped it would be around .230 - .240 but oh well I'm only shooting it out to around 200 yds.
I'm surprised it doesn't shoot better in your rifles as it's pretty much a govt. bullet with a flat point. If it shoots good enough it looks be an effective hunting bullet.

P.S. I just checked the Midway site and it's already out of stock. If it's a good bullet it was a good move and if not .....well you know.
Clarence
Posts: 2166
Joined: Tue Dec 24, 2002 7:38 pm
Location: Hill Country, TX

Post by Clarence »

I think the 1/4" +/- meplat will act much like the 457125. It may expand slightly more, but should still give good penetration.

On the other end of the spectrum, 3/8" meplat will definitely expand more, but will not penetrate as much (limited to 24-28" in my experience), and will generally be found under the skin on an angling shot, with pass-throughs only on broadside shots.

Clarence
pete
Posts: 2258
Joined: Tue Nov 12, 2002 10:16 pm
Location: Colorado

Post by pete »

Well I cast some pure lead speciman's and they are a good looking hunting bullet.
Having said that the nose measures .449 and after sizing and seating it's .450. The sizing operation obviously causes the nose to bump up a little with pure lead. At any rate it wouldn't chamber after 2 shots without using a dowel to force the cartridge in with. Sounds like a good hunting setup huh? I'll send it back to Midway with an explanation why. :roll: Saeco must make their molds catered towards smokeless shooters.
Clarence
Posts: 2166
Joined: Tue Dec 24, 2002 7:38 pm
Location: Hill Country, TX

Post by Clarence »

Pete,

If the pure lead bullet bumped up like you said, why are you sending the mould back to Midway? That's your problem, not the mould's.

Try casting it 30/1, be carefule when you run them through the lube-sizer and seater (either can bump the nose), and try again.

Clarence
pete
Posts: 2258
Joined: Tue Nov 12, 2002 10:16 pm
Location: Colorado

Post by pete »

Clarence;

I've had good luck with pure lead on animals with a Brooks 430 gr. flat point and Lyman 457132. I haven't had any problem with them or the Lyman govt. with regard to bumping up like I'm having with this bullet because the noses on those others are small enough to not be a factor. Lead really expands in a flat point and works good.
Post Reply