Mould Restoration

Discussions of powders, bullets and loading information.

Moderators: Kirk, Lucinda

User avatar
PhilRich
Posts: 71
Joined: Tue Jan 03, 2017 4:06 pm

Mould Restoration

Post by PhilRich »

I'm getting multiple prominant longitudinal seam lines on bullets from a BACO 45 cal money bullet mould. What is the best method to restore the mould to original condition?
Kurt
Posts: 8428
Joined: Wed Oct 12, 2005 10:28 pm
Location: Not Far enough NW in Illinois

Re: Mould Restoration

Post by Kurt »

Check the alignment pins. I had a couple moulds from Brooks and one from BA that gave me this problem. I found the pins where not the same hight above the block face and it held the blocks from completely closing. I used my loading press and adjust the pins. This cleared up the problem.
The reason a dog has so many friends is because he wags his tail instead of his tongue.

"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery"Winston Churchill
horsefly
Posts: 265
Joined: Mon Jan 05, 2004 8:59 pm
Location: West Texas

Re: Mould Restoration

Post by horsefly »

Good morning;

Before you blame the mould, look carefully at your technique. You can also get these marks if you are hitting the mould to bump loose a sticky bullet. If the blocks are too close together when you hit the handles (that's where you're hitting, right?) the half not holding the bullet can bump into the other side and mark the bullet.

The best solution is not to hit the mould at all. I assume you are using a stick on the mould. Tip the stuck bullet out with your thumb. If you have good gloves and do it quickly, you won't ever feel the heat.

Y'all be good.
horsefly
User avatar
PhilRich
Posts: 71
Joined: Tue Jan 03, 2017 4:06 pm

Re: Mould Restoration

Post by PhilRich »

horsefly wrote: Wed Apr 10, 2019 8:52 am Good morning;

Before you blame the mould, look carefully at your technique. You can also get these marks if you are hitting the mould to bump loose a sticky bullet. If the blocks are too close together when you hit the handles (that's where you're hitting, right?) the half not holding the bullet can bump into the other side and mark the bullet.

The best solution is not to hit the mould at all. I assume you are using a stick on the mould. Tip the stuck bullet out with your thumb. If you have good gloves and do it quickly, you won't ever feel the heat.

Y'all be good.
horsefly
Horsefly, I'm thinking this is probably what is happening and the reason for multiple longitudinal lines on the bullet. The bullets don't want to drop out easily.

Thanks,
Phil
Gussy
Posts: 1580
Joined: Mon May 05, 2008 2:37 pm
Location: WA, dry side
Contact:

Re: Mould Restoration

Post by Gussy »

I had a Lyman do that after many casting sessions. Where the pins go into for alignment was worn.

I pushed out the pins and put them on the opposite side..... Same as new alignment holes.

Sometimes just pushing the pins out a little more will also work. Run a stone over the holes to make sure there's not a burr.
Kurt
Posts: 8428
Joined: Wed Oct 12, 2005 10:28 pm
Location: Not Far enough NW in Illinois

Re: Mould Restoration

Post by Kurt »

I should have mentioned; close the mould, leave the sprue p[late open and look up at a light to see if you ess a line of light coming through. If you do there is a pin to high above the block halve holding the blocks apart. This will also cause a bullet to stick.
Also if your using a high antimony mix in the alloy let the bullet cool a little longer before opening the blocks.
The reason a dog has so many friends is because he wags his tail instead of his tongue.

"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery"Winston Churchill
User avatar
Lumpy Grits
Posts: 7673
Joined: Tue Jan 28, 2003 7:58 pm
Location: Springfield, Missouri-U.S.A. Earth

Re: Mould Restoration

Post by Lumpy Grits »

Be SURE there's no crud on the mould half's or crud build-up around the pins.
Drive the pins out a bit more.
Gary
"Hav'n you along, is like loose'n two good men"
User avatar
PhilRich
Posts: 71
Joined: Tue Jan 03, 2017 4:06 pm

Re: Mould Restoration

Post by PhilRich »

I have confirmed that the multiple lines are caused by tapping the handles too vigorously to release the bullet. It takes many light taps to release the bullet from the mould. I tried to gently pry the bullet out with a small screw driver - that doesn't work. I've been using the mould for 3 years, perhaps the surfaces aren't as smooth as they once were making release more difficult.

Thanks for the replies.
Coltsmoke
Posts: 1513
Joined: Sun Jul 04, 2010 8:55 am
Location: GA.

Re: Mould Restoration

Post by Coltsmoke »

How do you open the mold? Try pushing down on the right front corner at the bottom of the mold when you open it. If you use a glove hold the bottom of the mold together when you open it.
Normal isn't coming back, but Jesus is.
Gussy
Posts: 1580
Joined: Mon May 05, 2008 2:37 pm
Location: WA, dry side
Contact:

Re: Mould Restoration

Post by Gussy »

PhilRich wrote: Fri Apr 12, 2019 3:46 pm I have confirmed that the multiple lines are caused by tapping the handles too vigorously to release the bullet. It takes many light taps to release the bullet from the mould. I tried to gently pry the bullet out with a small screw driver - that doesn't work. I've been using the mould for 3 years, perhaps the surfaces aren't as smooth as they once were making release more difficult.

Thanks for the replies.
Do you smoke the mold so the bullet releases easier??
John Bly
Posts: 1078
Joined: Thu May 13, 2010 12:32 pm
Location: Stephens City, VA

Re: Mould Restoration

Post by John Bly »

It sounds like it needs a light lapping.
"Perfection consists not so much in doing extraordinary things as in doing ordinary things extraordinarily well"
John Boy
Posts: 506
Joined: Tue Apr 08, 2014 11:39 am

Re: Mould Restoration

Post by John Boy »

With the bullet in the mold, try tapping the handles nut only with your hickory stick - light tap. Will cause a vibration of the mold halves and with a 'tough' mold, several additional taps on the end of the handles will drop the stuck bullet
Regards
John
horsefly
Posts: 265
Joined: Mon Jan 05, 2004 8:59 pm
Location: West Texas

Re: Mould Restoration

Post by horsefly »

Good morning, PhilRich;

I'm happy that we were able to find what was causing your marks, but that is not really your problem. The real problem is that the block is not turning loose of the bullet. Is it the same side every time? You have gotten some good advice to clean the blocks well but carefully. I would look to see if that block is dirty or if the edge is banged some way. Soft iron moulds are easy to hurt. Use a magnifying glass and look carefully.

You also got some good advice about cleaning and about smoking the mould. If the blocks are clean, that helps. If there are divots or rough spots on the block, that won't help.

If there are deposits of some kind, clean carefully with a solvent and WOODEN implements like tooth picks or sticks from those good little cleaners with cotton on the end of a wooden stick. If you find one or more little divots of any sort in the edge of the cavity, come on back ... hopefully with some good close up photos.

Part of your trouble is that you are using that _)(*&^$%# stick to beat on the mould. Open the sprue with your hand (good leather glove) and then tap smartly once on the hinge with your stick if it makes you feel better. That should jar everything loose. You may also want to hold the bottom of the blocks when you open (as someone already suggested). If you need to remove the bullet, press the back of your index finger against the nose of the bullet and tip the base out with your thumb. That may take you some practice, but it really is a good way to do it.

Ideally, a tap on the hinge after you open the sprue by hand should drop the bullet. I know everybody does it, but I really don't like the idea of beating on the handles to get a bullet out. There are kinder and gentler ways.

Y'all be good;
horsefly
User avatar
PhilRich
Posts: 71
Joined: Tue Jan 03, 2017 4:06 pm

Re: Mould Restoration

Post by PhilRich »

I appreciate all of the "fatherly" advise and suggestions. Next week i will more closely examine the mould as to it's condition, clean it and further experiment with casting and bullet dropping technique.
User avatar
arnie
Posts: 1128
Joined: Sun Nov 24, 2002 6:54 pm

Re: Mould Restoration

Post by arnie »

I have found what works best for me to release a bullet from the mould .After cutting the sprue ,press the lower left rear corner down on your bench and put pressure on the upper right front corner with a piece of wood (mould mallet )and at the same time open the handles and the bullet will rotate slightly and fall out .This is similar to what Paul Jones recommends .
Post Reply