Barrel twist
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Barrel twist
I have a Borchardt with a 1-20 twist barrel. No issues, rifle shoots well. I bought a Ron Smith gain twist barrel 25 years ago that finishes 1-18. Thinking of installing it to the Borchardt. Question is, how much more accurate will the 1-18 be as opposed to my 1-20? Is it worth doing for whatever, if any, accuracy gain I may see?
Thanks. Frank.
NYC.
Thanks. Frank.
NYC.
-
- Posts: 2951
- Joined: Wed Feb 03, 2010 3:21 pm
- Location: Montana
Re: Barrel twist
45 caliber?
How far you shooting ?
How far you shooting ?
-
- Posts: 648
- Joined: Fri Nov 30, 2007 4:00 pm
Re: Barrel twist
never take something apart that's working art
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Re: Barrel twist
Sorry, 45/530 Postell. 1000 yds.
I have a Springfield trapdoor with a 1-22 twist and it seems to do well, as well as I can see the iron sights, at 1000. No tipping.
Thanks. Frank.
I have a Springfield trapdoor with a 1-22 twist and it seems to do well, as well as I can see the iron sights, at 1000. No tipping.
Thanks. Frank.
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Re: Barrel twist
The Borchardt in question is in 45-90. Most of my target 45's are 1-18. Some even suggest 1-16?
Not that experienced to make an informed decision.
Thanks. Frank.
NYC.
Not that experienced to make an informed decision.
Thanks. Frank.
NYC.
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Re: Barrel twist
I own two Shiloh sharps.LR experss. One 45-90, one 45-110. Both are 1-18 twist. Shot both at Kenny's ranch years ago and hit stuff.
I was younger then.
Thanks. Frank.
NYC.
I was younger then.
Thanks. Frank.
NYC.
- bpcr shooter
- Posts: 808
- Joined: Sun Feb 04, 2018 5:30 pm
- Location: Madison, Wi
Re: Barrel twist
the 20 barrels shoot just a tick shorter bullet than the 18's do. there probably wont be any increase in accuracy unless the barrel is made to tighter tolerances but, even then it will be questionable if its "better". You should see better accuracy in heavy/weird winds as the bullet should be more stable in said winds. If it were me I'd just leave well enough alone and build a rifle around the gain twist barrel.
But if you like to tinker......go for it!!
matt
But if you like to tinker......go for it!!
matt
NMLRA Member
Winnequah Gun Club Member (Lodi, Wi)
WIFORCE Member
SCI Member
Winnequah Gun Club Member (Lodi, Wi)
WIFORCE Member
SCI Member
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Re: Barrel twist
Matt,
Thanks for the reply, I'm installing a scope on this rifle, can't see through irons any longer. This is a built-up rifle so I'm not destroying originality. I'm sending it out to BRC for an overhaul. I'm sure this barrel will do more than I'm capable of at this point in my life.
Thanks. Frank.
NYC.
Thanks for the reply, I'm installing a scope on this rifle, can't see through irons any longer. This is a built-up rifle so I'm not destroying originality. I'm sending it out to BRC for an overhaul. I'm sure this barrel will do more than I'm capable of at this point in my life.
Thanks. Frank.
NYC.
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Re: Barrel twist
Matt,
Thanks for the reply, I'm installing a scope on this rifle, can't see through irons any longer. This is a built-up rifle so I'm not destroying originality. I'm sending it out to BRC for an overhaul. I'm sure this barrel will do more than I'm capable of at this point in my life.
Thanks. Frank.
NYC.
Thanks for the reply, I'm installing a scope on this rifle, can't see through irons any longer. This is a built-up rifle so I'm not destroying originality. I'm sending it out to BRC for an overhaul. I'm sure this barrel will do more than I'm capable of at this point in my life.
Thanks. Frank.
NYC.
-
- Posts: 2783
- Joined: Tue Jun 23, 2009 6:16 pm
Re: Barrel twist
Depending on the quality of the existing barrel, you might see an accuracy gain. Maybe not related to the twist change though. Ron Smith barrels are very good. I have a few of them and they are top notch.
Chris.
Chris.
-
- Posts: 79
- Joined: Sun Feb 14, 2010 10:30 pm
- Location: Brisbane Australia
Re: Barrel twist
Hi Frank , I would find a good quality round nose bullet length of 1.3ooinches that would come out at 500grains+ and go at it. Vic from down under
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Re: Barrel twist
Chris,
Will do.
Thanks.
Frank.
NYC.
Will do.
Thanks.
Frank.
NYC.
-
- Posts: 866
- Joined: Mon Jan 07, 2013 9:07 am
- Location: St. Albert, Alberta
Re: Barrel twist
The twist of the barrel will not affect accuracy unless the length of the bullet is significantly outside the gyroscopic stability range for that twist.
Cannot say if there will be an accuracy effect without knowing the final portion of the gain twist, as well as the length and caliber of your bullet plus the velocity you will be shooting it at.
Keep in mind dynamic stability for long range shooting is dependent on the bullet's nose shape and the center of gravity of the bullet which affects yaw and can increase wind sensitivity and accuracy.
The RKS (Ron Smith) barrel's accuracy mainly comes from a continuous choke along the entire taper.
These cut rifled barrels of 40 cuts per groove are meticulously machined with a CONTINUOUS tapered choke of 0.0004" from the breech to the muzzle.
This prevents gas cutting around of the side of the bullet as it progresses down the barrel - and that is how better accuracy is achieved.
Cannot say if there will be an accuracy effect without knowing the final portion of the gain twist, as well as the length and caliber of your bullet plus the velocity you will be shooting it at.
Keep in mind dynamic stability for long range shooting is dependent on the bullet's nose shape and the center of gravity of the bullet which affects yaw and can increase wind sensitivity and accuracy.
The RKS (Ron Smith) barrel's accuracy mainly comes from a continuous choke along the entire taper.
These cut rifled barrels of 40 cuts per groove are meticulously machined with a CONTINUOUS tapered choke of 0.0004" from the breech to the muzzle.
This prevents gas cutting around of the side of the bullet as it progresses down the barrel - and that is how better accuracy is achieved.
-
- Posts: 25
- Joined: Fri Oct 29, 2021 4:30 pm
Re: Barrel twist
Thanks for all of the replies and suggestions. I'm now more confused as to which way to go than before, LOL. Starting in 1992, I've shot my Shiloh's in competition at Quantico, and the Forbes range in Colonie, NY. Once I started shooting a Borchardt I had specially made with an 1-18, I was hooked on the user friendly Borchardt action. Still send a few rounds down the Shiloh's though. Reason for the current project is, I don't want to scope my other Borchardt since I had it built to Creedmoor specs.
Will update when decision made.
Thanks. Frank. NYC
Will update when decision made.
Thanks. Frank. NYC