Bullet casting
-
- Posts: 3817
- Joined: Wed Sep 25, 2002 1:22 pm
- Location: between No Where & No Place, WA
Re: Bullet casting
Addendum to the above:
Just checked my ladle and the spout was drilled out to 13/64".
Just checked my ladle and the spout was drilled out to 13/64".
Grand PooBah
WA ST F. E. S.
In real life may you be the bad ass that you claim to be on social media....
WA ST F. E. S.
In real life may you be the bad ass that you claim to be on social media....
-
- Posts: 1580
- Joined: Mon May 05, 2008 2:37 pm
- Location: WA, dry side
- Contact:
Re: Bullet casting
I filed a very thin groove down the side of the ladle spout. Let's the air out of the mould better.
- desert deuce
- Posts: 3867
- Joined: Mon Apr 14, 2008 10:51 pm
- Location: Rio Rico, Arizona
Re: Bullet casting
I have heard of, not used, the thin line filed on the spout of the ladle. Holding ladle in right hand where to locate the thin line?
I have seen, not used, a groove on the top of the sprue plate from the pour orifice to the edge. Holding mould in left hand where best to file groove?
Have not seen either in use.
Boring out the spout on the ladle is standard operating procedure though.
Filing the spout to meet the contour on the sprue plate a couple of times on a new ladle.
Sometimes opening up the orifice on the sprue plate was rarely done.
I clean up and smooth sprue plate faces with 600 grit wet dry sand paper on a perfectly flat surface, glass, using a circular motion.
On looking back over this thread I need to ask is there a best or preferred way to reset the locating pins after facing off the blocks ?
Have (carefully) spun a cast bullet from the blocks coated with fine abrasive in those same closed blocks. Worked like a charm.
I have seen, not used, a groove on the top of the sprue plate from the pour orifice to the edge. Holding mould in left hand where best to file groove?
Have not seen either in use.
Boring out the spout on the ladle is standard operating procedure though.
Filing the spout to meet the contour on the sprue plate a couple of times on a new ladle.
Sometimes opening up the orifice on the sprue plate was rarely done.
I clean up and smooth sprue plate faces with 600 grit wet dry sand paper on a perfectly flat surface, glass, using a circular motion.
On looking back over this thread I need to ask is there a best or preferred way to reset the locating pins after facing off the blocks ?
Have (carefully) spun a cast bullet from the blocks coated with fine abrasive in those same closed blocks. Worked like a charm.
Sometimes you get the chicken, and sometimes you get the feathers!
-
- Posts: 3857
- Joined: Tue Nov 23, 2004 12:52 pm
Re: Bullet casting
Have ladle poured for years out of 2 different RCBS Pro melt pots that have bottom pour valves. Having the melt at the right temp and mold at right temp are far more important to good bullets. On your first 10 casts when the puddle on the sprue plate solidify cut the sprue off then swing the plate back in position and count to 15 or so. Then swing the plate open and open blocks dropping the bullet on a padded surface. No magic juju here that extra count of fifteen is to heat the mold up faster to proper mold temp. If it helps great if it don?t what are you out? Bobw
bobw
-
- Posts: 1580
- Joined: Mon May 05, 2008 2:37 pm
- Location: WA, dry side
- Contact:
Re: Bullet casting
I'm right handed (hold mould handle in the left). Grove on the left side.
-
- Posts: 144
- Joined: Fri Feb 19, 2021 3:11 pm
- Location: Wv
Re: Bullet casting
Purchased a temp gun starting casting bullet looks better but looks like imperfections in parts and a frost glazing on parts any ideas?? Thanks
-
- Posts: 144
- Joined: Fri Feb 19, 2021 3:11 pm
- Location: Wv
Re: Bullet casting
. Temp in 800s. Brand new mold.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 144
- Joined: Fri Feb 19, 2021 3:11 pm
- Location: Wv
Re: Bullet casting
Cold it be air getting in mold? Should I drill out spout make a little bigger hole?? Thanks
-
- Posts: 174
- Joined: Thu Feb 16, 2023 3:08 pm
Re: Bullet casting
Hi what temp is it that you are casting the lead at? What type of casting are you doing ladle or bottom pour?
-
- Posts: 144
- Joined: Fri Feb 19, 2021 3:11 pm
- Location: Wv
Re: Bullet casting
Bottom pour. I’m down in 750.
-
- Posts: 144
- Joined: Fri Feb 19, 2021 3:11 pm
- Location: Wv
Re: Bullet casting
It’s like I get a lot of impurities around lube grooves. I have went high on temp same thing. I’m stumped lol
-
- Posts: 174
- Joined: Thu Feb 16, 2023 3:08 pm
Re: Bullet casting
Well in my 25 plus years of pouring i have never had any luck with the bottom pour pots always ended up like you to much crap in my bullets plug the hole off and use a ladle to cast from the top of the pot and your problem will be solved IMO
-
- Posts: 144
- Joined: Fri Feb 19, 2021 3:11 pm
- Location: Wv
Re: Bullet casting
here is one
You do not have the required permissions to view the files attached to this post.
-
- Posts: 174
- Joined: Thu Feb 16, 2023 3:08 pm
Re: Bullet casting
Like i said above they are not filling out right IMO it is due to the bottom pour i don't use or like them at all
they made me
they made me
-
- Posts: 144
- Joined: Fri Feb 19, 2021 3:11 pm
- Location: Wv
Re: Bullet casting
If you hand pour does the lard dipper hold enough can’t tell by pics. Looking at the RCBS ? Or are there a specific one to get?